![]() Port Vlans allowed and active in management domain Port Mode Encapsulation Status Native vlan ! Last configuration change at 06:30:23 UTC Mon May 15 2017 Vlan internal allocation policy ascending ! Last configuration change at 06:26:58 UTC Mon May 15 2017 Likewise, PC3 and VLAN10 will establish a healthy connection. When you ping from PC2 to PCs that are members of VLAN5, you can see that the process is successful. Check that the routing between VLANs is working properly. Now, ping the PC2 to the V2 member PC2 and test the connection. *Mar 1 00:09:18.259: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up In this step, open the command prompt by clicking R1 in the workspace to perform VLAN routing on a single cable on the Cisco Router and perform the following commands. Then, we have assigned the PCs to VLANs and made the Trunking connection. Up to this step, we have configured VPCS computers and created VLANs. VIOS-L2-01(config)#interface gigabitethernet 0/1 Use the following commands to perform the same operations on Cisco Layer 2 Switch-2. VIOS-L2-01(config)#interface gigabitethernet 0/0 VIOS-L2-01(config-if)#switchport mode trunk VIOS-L2-01(config-if)#switchport trunk encapsulation dot1q VIOS-L2-01(config)#interface gigabitethernet 0/3 ![]() VIOS-L2-01(config-if)#switchport access vlan 10 VIOS-L2-01(config)#interface gigabitethernet 0/2 VIOS-L2-01(config-if)#switchport access vlan 5 VIOS-L2-01(config-if)#switchport mode access vIOS-L2-01(config)#interface gigabitethernet 0/1 Use the following commands to determine the Access and Trunk interfaces of the Layer 2 Switch and to make PCs a member of VLANs. Configure the interfaces connected to the Cisco Router and L2 Switch as Trunk. I have some images but they run with QEMU which you need to have Vdt AMD technology activated on your VM (I'm not able to set this up on my environment).ĭo you know any L2 and 元 Switches images that run via Dynamips?.You must configure the L2 Switch interfaces. So I had to run the whole thing with a Remote Server which is running in Virtual Box, and I managed to run the Cisco IOS Router Images, along with the VCPS I'm almost done, I just need to be able to run the L2 and 元 Switches. And as I use linux I found it quite challenging as I couldnt install VMware, and Virtual Box is running funny. So I'm trying to set up the whole environment on my Laptop. I'm a bit on a halt of studying cause I wanted to switch from Cisco Packet Tracer to GNS3 which looks quite professional (although a bit daunting even for someone with experience already on the field). I'm carrying on studying, and everything fine, hope you are doing well as well guys. All opinions stated are those of the poster only, and do not reflect the opinion of Cisco Systems Inc., or its affiliates. NOTE: The "Reddit Cisco Ring", its associates, subreddits, and creator "mechman991" are not endorsed, sponsored, or officially associated with Cisco Systems Inc. Looking for work? check out /r/NetworkingJobs.Wireshark - For studying packets as they appear on the wire *FREE.Cisco Modeling Labs (CML) - Cisco's Network Simulator ($200/yr).EVE-NG - Another network simulator (FREE & Paid Options).GNS3 - The network simulator that every network person should have *FREE.Free Packet Tracer Download - *FREE WITH SIGNUP.Networking Fundamentals - Learn the very core of Networking.Cisco's Learning Network - Look here no matter what you do.Packet Life Cheat Sheets - Don't forget to thank /u/stretch85 and remind him to update his sheets.- Subnetting practice site built by redditor /u/DressedUpNowhere2Go.Subnetting Tutorial and Problem Generator.Free Resources to Prepare for CCNA - from Practical Networking.Proof Cisco bans known cheaters!ħ) Limited Self-Promotion permitted only from contributing members to the Subreddit, if it's in good taste and not excessive. A gathering place for CCNA's, or those looking to obtain their CCNA! Rulesġ) No posting of illegal materials (torrents, stolen PDFs, etc)Ģ) No posting of "braindumps" (this includes 9tut)Ĥ) Do not ask for others to do your labs for you, or solicit payment for labs to be done for you.ĥ) This sub is not intended for tech support questions, you would be better off asking such questions in /r/networking or /r/cisco since this sub is by definition a novice community that is trying to learn networking fundamentals.Ħ) Make sure you are not violating the Cisco testing NDA (Non Disclosure Agreement)! Do not post questions you saw on the exam.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |